Clone-A-Willy Kit

This product is def worth a try. Was fun to make with my wife. Its not rocket science, but ya better plan ahead for sure. My first one didnt turn out that great because I used too big of a mixing bowl and couldnt get all the gel out in a timely manner. Def takes 2 people to pull this one off. Also would recommend using a cock ring or something to keep it full erect. I had my wife working on me while I prepared everything, worked ok. But still 2mins is not much time. If somehow you mess up the molding process, clone a willy sells the mixing powder on its site so you dont have to buy a whole new kit. GL and have fun!!!!!!!

My boyfriend and I bought this and used it not to long ago. Apparently he is part of the "4%" that this product mentions. He is somewhat large...a lil over 8 inches in length and roughly 6 inch girth...so for anyone with these measurements (give or take...or larger) this kit will cause issues. The tube itself was long enough and did not cause problems. However, the instructions say to slowly rotate the tube if any of your pecker is touching the inside wall. Due to his girth this was somewhat hard to do. He could not get it twisted enough to where at least a bit of his pecker was touching the sides of the inner part of the tube directly. We had bought two kits (two different colors) and this occured with both of the kits. Secondly, due to his length/girth...there was not enough rubber to fill the entire mold. We did the first kit and used the 5 inch vibrator that came with the kit. When we put as much of the rubber that we could inside, there was at least 2-3 inches or more that was empty on the top. We inserted the vibrator and it did not push the rubber high enough to fill the rest of the space. It probably filled about an inch or so but there was still more room that was not filled. We went and looked back on the instructions and it mentioned that if you have a larger pecker, to use a 7 inch vibrator instead of the 5 inch standard that came with the kit. So, we went out later that night to a toy shop...we found a 7 inch vibrator (roughly the same type/thinness of the one in the kit). We used the second kit along with the 7 inch vibrator that we bought. It still did not fill the rest of the empty space. It did help but there was still some empty space that did not get filled. If you happen to have a larger pecker similar to that of my boyfriends, I strongly reccomend buying the extra rubber for the kit or finding a very thin but long vibrator to help push the rubber into those empty spaces. Aside from that the kit is great. Be fast, use a stop watch or a timer when you are mixing the powder for the mold...it helped greatly. Two people is a must. Read the instructions a few times...and if you go to the clone a willy website there is a "how-to" video that is very useful as well...I stronly reccomend watching/reading everything prior to the first use.

This was fun to create and it comes in handy when wifey and I are feeling kinky....this was the only way to coax her into a DP. A little awkward to make while maintaning an erection, but we pulled it off. As was said before, FOLLOW THE INSTRUCTIONS!

Most important to shave ahead of time...or else have someone you trust with sissors afterward!! We used a plastic tablecloth on the floor to help with the mess, and make sure you have all your ingredients out, and read the instructions CAREFULLY ahead of time, not hard to do but must be quick to do well. Definately easier with someone to help. He kept himself hard while I did the mixing. A cock ring is a good idea. It takes 24 hours to be completely finished. If you have kids like us it is helpful to do it in stages: cut the plastic tube in advance, have to be erect to do this to know how long to cut the tube, and put on tape in one session and can finish in another session if needed. Also can be difficult to get an accurate length if you are fighting constantly to keep up the erection all the time. Cutting the sealed end makes good sense but we did not think of that. We got the water hotter than it said so we could work up the erection a little before dipping in the mold. Our biggest issue was he was touching the side of the tube. Good idea to check for that before it sets up. Because of this dildo is thin and the vibrator looks as if it may come out in the near future. If it does we will definately make another! Very life like...love it!!

I bought this to make a replica of my husband, and it worked great!! I followed the advice of people on here and had him lay down, then we cut off the sealed end. After he was ready, we put the tube over him, and I poured in the mixture around him. It was messy because I used a large bowl to mix the powder & water, and pouring from that huge bowl into that tube was not the best idea! Oh well! Still worked amazingly... One more word of advice though- Trim your man's hair down there because if some of it is in the tube around the base of him, it will be harder for him to pull out of the tube once the mold hardens... his hair was stuck in the hardened mold! That difficulty made a tear in the bottom of our mold, so later on some of the rubber stuff leaked out of that part... All that resulted was a slightly shorter replica of him... we'll probably try again so I can make one with his full length. We just watched a porn DVD while doing this, and I made sure he focused on that, and he stayed hard with no problem... I can't wait to try this again!! It's great! I love the replica, it's so exact!!!!

This is a good product. It is tricky though. I read the reviews first, and that helped me. Be sure to put something down, that you can throw away, on the floor when you do this. It's very messy. Also, have someone help you stay hard. Either by touching or visual stimulation. If you use a coc*ring, it will come out in the mold. I used one. I think it made the clone look less realistic. When you mix the powder into the water, don't try to mix it very well(It's supposed to be lumpy). It takes too long and it gets hard very fast. I don't recommend waiting at all, before inserting your penis. Just do it quick and press it against your body to keep it from spilling out. Don't get discouraged after your first attempt. You can order more powder. It's really cheap for that stuff. The liquid rubber is the expensive part, so make sure you're happy with the mold before pouring the rubber.

Sounds like a great item but first the directions need help. Heat water above 98 degrees bc it cools toooo quick .second put your willy in the tube and cut the tub so the tub is open on both ends. After mixing insert your willy and thin have someone poor it in over your willy. Other then that it is great.

My girlfriend and I had one of the HOTTEST nights ever molding my penis! It was really easy to do and I don't understand enyone who had a problem. All you have to do is follow the directions (they even have simple to follow pictures) and you will have an exact copy of yourself. Unbelievable. Making the mold felt kinda good too. It was really warm. Something new I could actually put my dick into that didn't get me in trouble! We've already told all of our friends. Now whenever I'm away, my girlfriend has my best part with her.<BR> <BR>

After having tried this product twice, once by myself and once with her help.. both attempts failed miserably. We are relatively intelligent and can follow directions, I/we used a stopwatch for timing and for the second evena digital thermometer and still failure. so after $60.00 into this we are scrapping the idea. I would like to publish my name to add credibility to this review but privacy concerns outweigh the credibility issue..the only reason I did not rate it as terrible is it was amusing to attempt it and when she was helping it led to fun anyway. try it if you want to.. but I would not recommend this to anyone.

This was alot of fun for me and my husband to use. It was easy and we even got a second one because of how much we enjoy using it and making it. A must have for anyone in a military relationship or anyone who just likes experamenting. My husband and I both really enjoy this one.